Where is dell inspiron hard drive located

Download any programs or files that you want to keep onto another storage device like a CD or external hard drive. Remember to delete any personal information or private files before removing the old hard drive. Turn off the power button of your Dell computer tower and let the CPU shut down. Disconnect the power cord from your electrical outlet, and then detach the cord from the back of the CPU. Unfasten the screws on the back of the tower with a screwdriver, so that the case can be opened.

Swing the cover of the CPU case open to reveal the inside of the case. Locate the silver colored, 2-byby-6 inch metal hard drive in the frame bracket at the top of the case near the front of the CPU, and find the white plastic electrical IDE connectors that are plugged into the back of the hard drive. Video Card. Palm Rest Assembly.

Reserve Battery. System Board Assembly. Battery and Media Bay Latch Assemblies. Battery Charger Board. LED Board. Fan Assembly. Before removing and replacing components, photocopy the screw placemat as a tool to lay out and keep track of the screws. The placemat provides the number of screws and the sizes.

Hard Drive Door Security :M3 x 5 mm 1 each. You must remove the optional Mini PCI card assembly before the system board assembly can be removed. A Mini PCI card assembly may consist of a modem, a network adapter, a modem and network adapter combination, or a wireless network adapter. A modem, network adapter, or modem and network adapter combination must be connected to the wiring harness as appropriate; a wireless network adapter must be connected to the system's internal antenna.

The bezel is secured to the display assembly top cover with plastic tabs around the sides. Use a plastic scribe to help separate the bezel from the top cover. When the microprocessor module is correctly seated, all four corners are aligned to the same height. If one or more corners of the module are higher than the others, the module is not seated correctly.

The system board's BIOS contains the system service tag number, which is also visible on a bar-code label on the bottom of the computer. The replacement kit for the system board assembly includes a floppy disk or CD that provides a utility for transferring the service tag number to the replacement system board assembly. Apply downward pressure to the tabs while squeezing them together tweezers work well to eject the latch button from the bottom of the case without loosening the upper latch assembly spring and slider.

If the upper latch assembly does come loose:. Align the screw holes on the battery charger board with the screw holes on the bottom case assembly, and then press the battery charger board down into its connector. To replace a connector cover, orient the cover notch-side-up and snap it into the connector cutout. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty.

Most likely if you're reading this you are either trouble shooting the computer and looking to reseat the hard drive or you are replacing the current hard drive. After reading this instructable you will know how to do both of these depending on your situation. While the instructions found in this instructable are meant specifically for the Dell Inspiron 15 Series, many of the steps should apply to other similar Dell laptops as well.

I decided to make this instructable because whenever I tried to turn on my laptop, a message would pop up saying 'hard drive not installed', even though it was. I proceeded to do some research and performed some diagnostics tests with my laptop until I received the error code ''. With some additional research I was able to conclude that I simply needed a new hard drive.

I managed to figure out how to remove the drive on my own and figured that I would make an instructable to show others how access theirs as well. Start by removing the battery. The battery will pop up and can then be removed and set aside. Next you can remove all of the visible screws with your screwdriver. There are two unique variants of screws; in the photo above, the 7 screws circled in blue are all the same and are longer than the 3 screws circled in red.

Remove the screws and either use a pair of tweezers or a small magnet to remove the screws from their holes you can also flip the computer over to remove them but be careful not to lose any! Once you have the screws removed, put them in whatever container you have for storing them so that you do not lose any. If you think you might have trouble identifying the difference between the screws upon reassembly, separate them into individual baggies so that you do not mix them up.

You will now begin removing the keyboard. Flip the computer right side up and open it. Along the top edge of the keyboard you will see 5 small slots. Using your straight edge, pry the board up from each of these points, being careful not to damage any part of the keyboard. Once the top of the board has been pried up, it should be able to angle towards you. With the board making about a 45 degree angle from the computer, it will slide out away from you.

Flip the board upside down by rotating the top of the board towards you and then set it down on the track pad and palm rests. With the keyboard flipped upside down, you will now see a large ribbon connecting the keyboard to the computer and a smaller ribbon labeled 'ODD'. Each of these ribbons have small black plastic retainers holding them in place which can be seen in the second picture above. Using your fingernail, flip the retainer up.

Now gently pull out the ribbon for the keyboard This may not be the same for your computer, but I found that when I went to remove my keyboard ribbon, it was much more difficult to pull out then the other ribbons discussed in this instructable, so be careful!

Now you can set aside the keyboard along with the battery. Repeat the process for removing ribbons that you just did on the previously mentioned 'ODD' ribbon. But for his one, only remove it from the retainer and leave it as is. Now that you have the keyboard removed and out of the way, you can finish this step by removing the 5 screws that were hidden under the keyboard.